Produse pentru pour adânc epoxid (13)

EPOXY RESINS

COMPOSITION ET ASPECT Blanche. CONDITIONNEMENTS Cartouche de 290 ml. STOCKAGE 12 mois à l’abri du froid et des fortes chaleurs en emballage d’origine non entamé. CARACTÉRISTIQUES TECHNIQUES • Matières premières : MS Polymère • Système de durcissement : par l’humidité • V itesse de durcissement : 2,5 à 3 mm par 24 h. (à T=23°C et 50 % HR) • Formation de peau : 10 à 15 minutes (à T = 23°C et 50 % HR) PRÉCAUTIONS D’EMPLOI Ne pas travailler en dessous de +5°C. Conserver hors de portée des enfants. Contient : N-(3-(trimethoxysilyl)propyl)ethylenediamine - Bis(1,2,2,6,6-pentamethyl-4-piperidyl) sebacaat - Methyl1,2,2,6,6-pentamethyl-4-piperidyl sebacaat. Peut déclencher une réaction allergique. PRÉPARATION DES SUPPORTS Les supports doivent être propres, secs, dépoussiérés et dégraissés. APPLICATION Appliquer la colle en extrudant un cordon ou des points sur le support ou l’élément à coller. Assembler les matériaux le plus vite possible : maxi 10 minutes. • Poids spécifique...

2component epoxy paint for the protection of concrete floors, metal structures, etc. Does not contain solvents (100% solids). Features Excellent adhesion. Great penetration power. Good adhesion in wet substrate with high percentage of humidity. Good capacity for reaction at low temperatures and high percentage of humidity. Indoor and outdoor use.

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

SUPER NETTOYANT SOLS LISSES 97.8 des ingrédients d’origine naturelle Idéal nettoyages difficiles – Contact alimentaire Nettoyant sols très concentré, idéal pour le nettoyage difficile des sols cimentés, carrelés ou peints. Convient également pour le décapage d’émulsions autolustrantes. Application manuelle ou en autolaveuse. pH > 12. Formulation sur base végétale. 97,8% du total des ingrédients sont d’origine naturelle. Contact alimentaire (arrêté du 19/12/2013). Réf:I536 Conditionnement:Bidon de 5 L – Carton de 4

Protech AC-P Paint based on acrylic resins in aqueous emulsion, for interiors and exteriors, protective lamellar structure which, in addition to having an aesthetic effect, allows maximum filling, transpiration and very high resistance to mechanical and chemical light. The high coverage and expandability make this product extremely easy to apply. The special acrylic resins that compose it allow to obtain a film characterized by a rapid insensitivity to water even during the drying phase, with a consequent reduction of the "snail effect" in the event of atmospheric events. Protective and decorative finish painting of walls, facades, concrete products, plasters, masonry, natural stone, porous substrates in general. For old plasters, pay particular attention to the old pre-existing paints, which must be removed by careful scraping and brushing in order to obtain a healthy and non-friable support; then proceed with the application of Protech Fix AC fixative. When applying on new plasters, it is good practice to insulate the base with acrylic insulator or even better with a white or neutral microemulsion fixative. Avoid windy or cold days when applying. Do not apply on fresh or particularly alkaline substrates, respect a minimum carbonation period of at least four weeks. On large surfaces it is recommended to apply product from the same batch and always proceed wet on wet to avoid signs of recovery. Never operate with temperatures below + 5 ° C. Rainy weather, excessive atmospheric humidity and temperatures below + 8 ° C can greatly compromise drying with the possibility of washing off by rainwater even after several days. . DILUTION (by volume with drinking water) BRUSH 1st COAT: 15% a crossed coat or two coats 12-24 hours apart 2nd COAT: 10%. ROLLER 1st COAT: 10% 2nd COAT: 10%. SPRAY (through specific equipment) 1st COAT: 15/25% 2nd COAT: 15/25%. To avoid filming defects, being resin-based products in aqueous emulsion, the application temperature must be between + 5 ° C and + 35 ° C with relative humidity not higher than 60/70%. Do not apply under the direct action of the sun and wind. Do not apply on fresh or particularly alkaline substrates, respect a minimum drying period of the substrate of at least four weeks. It is also advisable for colored, not to use on large surfaces dyed with different production batches as slight differences between batch and batch are technically possible. Please check the color before application as we will not respond to any disputes regarding the shade of the applied product. From 0.20 to 0.30 liters of Protech AC-P for each square meter of surface to be painted. Pail 14 l

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Protech Fix AC-Therm Water-based anti-condensing wall covering, with excellent fixing and anchoring properties, with good coverage based on high penetration acrylic resins, 3M Glass Bubble, pigments, fillers and covering fillers. Suitable as an anti-condensation fixative primer, prior to painting or coating the plaster with anti-condensation paints or plasters (-THERM). Ideal for interventions on walls with mucilage deposits, bacterial phenomena and moulds. Due to its low thermal conductivity, it is particularly suitable for solving mould problems. It can be applied on any plaster (rustic, civil, plaster, dry mortar, plasterboard, concrete, prefabricated, exposed concrete, etc.). Made with special resins and additives it reduces the absorption of the support while allowing the necessary transpiration, uniforms the absorption making the application of the finishing coats easier. It always works in depth, which is why it is the ideal preparation for applying water-based paints or coatings. Adhesion is excellent even on particularly difficult surfaces, thanks to the use of special resins and the presence in the formulation of an adhesion promoter interacting between the support and the product. Preliminary treatment of any surface (civil, plaster, rustic, dry mortars, plasterboard, concrete, prefabricated, exposed concrete etc.) designed to isolate the support surfaces and standardise the absorptions of the subsequent anti-condensate treatments (painting and protective coatings). Packaging: 14-liter bucket UM: €/l

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Gel microbilles sans solvant, salissures fortes Excellentes performances nettoyantes – Parfum orange frais et tonique – Testé sous contrôle dermatologique Pour graisses, lubrifiants, cambouis, hydrocarbures, goudron, poussières freins, peintures fraîches. La texture adhérente du savon gel microbilles AEXALT Orange n’agresse pas la peau et se rince facilement. Le gel laisse un touché doux sur l’épiderme et une discrète odeur citronnée. Idéal dans les ateliers, sur les chantiers, les services de maintenance, en imprimerie, etc. NB : les gels microbilles AEXALT sont formulés avec des abrasifs d’origine naturelle. Réf:SA671 Conditionnement:Pot de 5 L, Seau de 15 L, Seau de 25L Parfum:Orange Ex:AEXALT ORANGE

Absorbant huiles et hydrocarbures, fioul Absorbe rapidement les taches d’huiles, d’essence, de cambouis, de gras et de peinture. Assure la propreté et la sécurité des sols où il y a la présence d’huile ou autres liquides. Peut absorber jusqu’à 150% de son volume (en fonction de la substance). Également recommandé pour le sol de la cuisine en cas de présence de gras important. Destiné aux professionnels chargés d’interventions nécessitant une absorption très rapide : plombiers, nettoyage des parkings extérieurs et intérieurs, transports des liquides, risque de pollution etc, tous les garages et toutes les stations services, les cuisines de collectivités, les arrêts de bus en ville, les industries… Réf:AB830 Conditionnement:Boite poudreuse 1 L – Carton de 6 Ex:AEXASORB'UIL

Débloque et lubrifie les pièces grippées avec une grande efficacité. Compatible avec tous les métaux. Produit particulièrement mouillant. Il pénètre rapidement entre les surfaces oxydées, disperse la rouille, les salissures et les dépôts divers pour libérer les mécanismes corrodés ou coincés. Laisse un film gras très mince formant une barrière protectrice contre l’eau et l’oxygène. Diminue le frottement entre les pièces mécaniques et les plastiques. Une action prolongée permet d’éliminer les traces de rouille, cambouis, goudron, colle, adhésif, résine ou calamine même brûlée. Protège les métaux sans agressivité vis-à-vis des peintures et caoutchoucs. Chasse l’humidité et assure des contacts électriques parfaits. Appliqué au montage, il assure une protection de longue durée en s’opposant à l’accrochage de la rouille sur le métal. Compatible avec tous les métaux et la plupart des plastiques, peintures, etc. Réf:AO773 Conditionnement:Bidon de 5 L – Carton de 4, Fût de 220 L

Savon gel microbilles solvanté – idéal pour mécaniciens, en ateliers ou en imprimerie Tous types de salissures et salissures fortes – Agréablement parfumé – Testé sous contrôle dermatologique Gel avec solvant idéal pour venir à bout des salissures les plus tenaces : graisses, lubrifiants, cambouis, hydrocarbures, goudron, poussières freins, vernis, encres.. La présence d’un agent compensateur protège l’épiderme et laisse celui-ci particulièrement doux après usage. NB : les gels microbilles AEXALT sont formulés avec des abrasifs d’origine naturelle. Réf:SA602 Conditionnement:Cartouche 4 Litres – Carton de 2 Ex:AEXALT GELEM